| Current File : //proc/thread-self/root/usr/src/linux-headers-6.8.0-59/drivers/net/ethernet/realtek/Kconfig |
# SPDX-License-Identifier: GPL-2.0-only
#
# Realtek device configuration
#
config NET_VENDOR_REALTEK
bool "Realtek devices"
default y
depends on PCI || (PARPORT && X86)
help
If you have a network (Ethernet) card belonging to this class, say Y.
Note that the answer to this question doesn't directly affect the
kernel: saying N will just cause the configurator to skip all
the questions about Realtek devices. If you say Y, you will be asked for
your specific card in the following questions.
if NET_VENDOR_REALTEK
config ATP
tristate "AT-LAN-TEC/RealTek pocket adapter support"
depends on PARPORT && X86
select CRC32
help
This is a network (Ethernet) device which attaches to your parallel
port. Read the file <file:drivers/net/ethernet/realtek/atp.c>
if you want to use this. If you intend to use this driver, you
should have said N to the "Parallel printer support", because the two
drivers don't like each other.
To compile this driver as a module, choose M here: the module
will be called atp.
config 8139CP
tristate "RealTek RTL-8139 C+ PCI Fast Ethernet Adapter support"
depends on PCI
select CRC32
select MII
help
This is a driver for the Fast Ethernet PCI network cards based on
the RTL8139C+ chips. If you have one of those, say Y here.
To compile this driver as a module, choose M here: the module
will be called 8139cp. This is recommended.
config 8139TOO
tristate "RealTek RTL-8129/8130/8139 PCI Fast Ethernet Adapter support"
depends on PCI
select CRC32
select MII
help
This is a driver for the Fast Ethernet PCI network cards based on
the RTL 8129/8130/8139 chips. If you have one of those, say Y here.
To compile this driver as a module, choose M here: the module
will be called 8139too. This is recommended.
config 8139TOO_PIO
bool "Use PIO instead of MMIO"
default y
depends on 8139TOO
help
This instructs the driver to use programmed I/O ports (PIO) instead
of PCI shared memory (MMIO). This can possibly solve some problems
in case your mainboard has memory consistency issues. If unsure,
say N.
config 8139TOO_TUNE_TWISTER
bool "Support for uncommon RTL-8139 rev. K (automatic channel equalization)"
depends on 8139TOO
help
This implements a function which might come in handy in case you
are using low quality on long cabling. It is required for RealTek
RTL-8139 revision K boards, and totally unused otherwise. It tries
to match the transceiver to the cable characteristics. This is
experimental since hardly documented by the manufacturer.
If unsure, say Y.
config 8139TOO_8129
bool "Support for older RTL-8129/8130 boards"
depends on 8139TOO
help
This enables support for the older and uncommon RTL-8129 and
RTL-8130 chips, which support MII via an external transceiver,
instead of an internal one. Disabling this option will save some
memory by making the code size smaller. If unsure, say Y.
config 8139_OLD_RX_RESET
bool "Use older RX-reset method"
depends on 8139TOO
help
The 8139too driver was recently updated to contain a more rapid
reset sequence, in the face of severe receive errors. This "new"
RX-reset method should be adequate for all boards. But if you
experience problems, you can enable this option to restore the
old RX-reset behavior. If unsure, say N.
config R8169
tristate "Realtek 8169/8168/8101/8125 ethernet support"
depends on PCI
select FW_LOADER
select CRC32
select PHYLIB
select REALTEK_PHY
help
Say Y here if you have a Realtek Ethernet adapter belonging to
the following families:
RTL8169 Gigabit Ethernet
RTL8168 Gigabit Ethernet
RTL8101 Fast Ethernet
RTL8125 2.5GBit Ethernet
To compile this driver as a module, choose M here: the module
will be called r8169. This is recommended.
config R8169_LEDS
def_bool R8169 && LEDS_TRIGGER_NETDEV
depends on !(R8169=y && LEDS_CLASS=m)
help
Optional support for controlling the NIC LED's with the netdev
LED trigger.
endif # NET_VENDOR_REALTEK